Bewise Inc. www.tool-tool.com Reference source from the internet.
瑕疵常用词汇
defective product label不良标签
identifying sheet list标示单
screwdriver holder起子插座
aberration 色差
atomization 霚化
bank mark 滞料纹
bite 咬入
blacking hole 涂料孔(铸疵)
blacking scab 涂料疤
blister 起泡
blooming 起霜
blow hole 破孔
blushing 泛白
body wrinkle 侧壁皱纹
breaking-in 冒口带肉
bubble 膜泡
burn mark 糊斑
burr 毛边
camber 翘曲
cell 气泡
center buckle 表面中部波皱
check 细裂痕
checking 龟裂
chipping 修整表面缺陷
clamp-off 铸件凹痕
collapse 塌陷
color mottle 色斑
corrosion 腐蚀
crack 裂痕
crazing 碎裂crazing 龟裂
deformation 变形
edge 切边碎片
edge crack 裂边
fading 退色
filler speak 填充料斑
fissure 裂纹
flange wrinkle 凸缘起皱
flaw 刮伤
flow mark 流痕
galling 毛边
glazing 光滑
gloss 光泽
grease pits 污斑
grinding defect 磨痕
haircrack 发裂
haze 雾度
incrustation 水锈
indentation 压痕
internal porosity 内部气孔
mismatch 偏模
mottle 斑点
necking 缩颈
nick 割痕
orange peel 橘皮状表面缺陷
overflow 溢流
peeling 剥离
pit 坑
pitting corrosion 点状腐蚀
plate mark 模板印痕
pock 麻点
pock mark 痘斑
resin streak 树脂流纹
resin wear 树脂脱落
riding 凹陷 sagging 松垂
saponification 皂化
scar 疤痕
scrap 废料
scrap jam 废料阻塞
scratch 刮伤/划痕
scuffing 深冲表面划伤
seam 裂痕
shock line 模口挤痕
short shot 充填不足
shrinkage pool 凹孔
sink mark 凹痕
skin inclusion 表皮折迭
straightening 矫直
streak 条状痕
surface check 表面裂痕
surface roughening 橘皮状表皮皱折
surging 波动
sweat out 冒汗
torsion 扭曲
warpage 翘曲
waviness 波痕
webbing 熔塌
weld mark 焊痕
whitening 白化
wrinkle 皱纹
missing part漏件
wrong part错件
excessive defects过多的缺陷
critical defect极严重缺陷
major defect主要缺陷
minor defect次要缺陷
not up to standard不合规格
dimension/size is a little bigger尺寸偏大(小)
cosmetic defect外观不良
slipped screwhead/slippery screw head螺丝滑头
slipped screwhead/shippery screw thread滑手
speckle斑点
mildewed=moldy=mouldy发霉
rust生锈
deformation变形
burr(金属)
flash(塑件)毛边
poor staking铆合不良
excesssive gap间隙过大
grease/oil stains油污
inclusion杂质
painting peel off脏污
shrinking/shrinkage缩水
mixed color杂色
scratch划伤
poor processing 制程不良
poor incoming part事件不良
fold of pakaging belt打包带折皱
painting make-up补漆
discoloration羿色
water spots水渍
polishing/surface processing表面处理
exposed metal/bare metal金属裸露
lack of painting烤漆不到位
qualified products, up-to-grade products良品
defective products, not up-to-grade products不良品
waste废料
流道浇口部分
runner system浇道系统
sprue/cold material trap 浇道/冷料井
sprue puller 拉杆
runner design 流道设计
main runner 主流道
secondary runner 次流道
gate design 浇口设计
submarine gate 潜伏浇口
tunnel gate 隧道式浇口
pinpoint gate 点浇口
fan gate 扇形浇口
side gate 侧浇口
edge gate 侧缘浇口
tab gate 搭接浇口
film gate 薄膜浇口
flash gate 闸门浇口
slit gate 缝隙浇口
dish gate 盘形浇口
diaphragm gate 隔膜浇口
ring gate 环形浇口
Runner less 无浇道
(sprue less) 无射料管方式
long nozzle 延长喷嘴方式
sprue 浇口;溶渣
insulated runner/hot runner 热浇道
runner plat 浇道模块
valve gate阀门浇口 slag well 冷料井
cold slag 冷料渣
sprue gate 射料浇口，直浇口
nozzle 射嘴
sprue lock pin 料头钩销(拉料杆)
injection mold 注塑模
rubber molding 橡胶成形
hot chamber die casting 热室压铸
sand mold casting 砂模铸造
extrusion mold 挤出模
multi-cavity mold 多模穴模具
palletizing die 叠层模
plaster mold 石膏模
three plates mold 三板模
plain die 简易模
pierce die 冲孔模
forming die 成型模
progressive die 连续模
gang dies 复合模
shearing die 剪边模
riveting die 铆合模
compre sion molding 压缩成型
flash mold 溢流式模具
plsitive mold 挤压式模具
split mold 分割式模具
cavity 型控 母模
core 模心
公模注塑缺陷
flash 飞边
warpage 翘曲
air trap 积风
blush 发赤
flow line 流痕
splay 银纹
short shot 短射
sink mark 缩痕
streak 条纹
void 缩孔
weld line 熔接线
gas mark 烧焦
cold slug 冷斑
delamination 起皮
burr 毛刺
flaw/scratch 刮伤
gloss 光泽
glazing 光滑
surface check 表面裂痕
hesitation 迟滞注塑工艺:
molding conditions 成型条件
drying 烘干
barrel temperature 料筒温度
melt temperature 熔化温度
mold temperature 模具温度
injection pressure 注塑压力
back pressure 背压
injection speed 注塑速度
screw speed 螺杆转速
tensile strength 抗拉强度
tensile elongation 延伸率
flexural modulus 弯曲模数
flexural strength 抗弯强度
shrinkage 收缩率
regrind usage 次料
使用机械设备
lathe车床
planer |刨床
miller 铣床
grinder 磨床
driller 钻床
linear cutting 线切割
electrical sparkle 电火花
welder 电焊机
punching machine 冲床
robot机械手
common equipment常用设备
EDM=Electron Discharge Machining 放电加工
3D coordinate measurement 三次元量床 boring machine 搪孔机
milling machine 铣床
contouring machine 轮廓锯床
copy grinding machine 仿形磨床
cylindrical grinding machine 外圆磨床
die spotting machine 合模机
engraving machine 雕刻机
engraving E.D.M. 雕模放置加工机
form grinding machine 成形磨床
graphite machine 石墨加工机
horizontal boring machine 卧式搪孔机
horizontal machine center 卧式加工制造中心
internal cylindrical machine 内圆磨床
检验量测工具用语
autocollimator 自动准直机
bench comparator 比长仪
block gauge 块规
bore check 精密小测定器
calibration 校准
caliper gauge 卡规
check gauge 校对规
clearance gauge 间隙规
clinoretee 测斜仪
comparator 比测仪
cylinder square 圆筒直尺
depth gauge 测深规
dial indicator 针盘指示表
dial snap gauge 卡规
digital micrometer 数位式测微计
feeler gauge 测隙规
gauge plate 量规定位板
height gauge 测高规
inside calipers 内卡钳
inside micrometer 内分卡
interferometer 干涉仪
leveling block 平台
limit gauge 限规
micrometer 测微计
mil 千分之一寸
monometer 压力计
morse taper gauge 莫氏锥度量规
nonius 游标卡尺
optical flat 光学平晶
optical parallel 光学平行
passimeter 内径仪
position scale 位置刻度
profile projector 轮廓光学投影仪
protractor 分角器
radius 半径
ring gauge 环规
sine bar 正弦量规
snap gauge 卡模
square master 直角尺
stylus 触针
telescopic gauge 伸缩性量规
working gauge 工作量规
焊接用语
acetylene 乙炔
ampere 电流安培
angle welding 角焊
arc 电弧
argon arc welding 氩弧焊接
bare electrode 光熔接条
butt welding 对接焊接
camber 电弧弯曲
cascade 阶叠熔接法
clad weld 被覆熔接
crator 焊疤
excess metal 多余金属
filler rod 焊条
fillet weld 填角焊接
gas shield 气体遮蔽
groove welding 起槽熔接
hand face shield 手握面罩
hard facing 硬表面堆焊
jig welding 工模焊接
laser beam welding 雷射光焊接
metal electrode insert gas welding MIG熔接
nugget 点焊熔核
overlaying 堆焊
peening of welding 珠击熔接法
plug welding 塞孔熔接
positioned welding 正向熔接
pressure welding 压焊
propane gas cutting 丙烷气切割
pure nickel electrode 纯镍熔接条 reinforcement of weld 加强焊接
resist 抗蚀护膜
root running 背面熔接
seam 焊缝
seaming 接合
seam welding 流缝熔接
series seam welding 串联缝熔接
skip welding process 跳焊法
spark 火花
spot welding 点焊接
stitch welding 针角焊接
stud arc welding 电弧焊接
under laying 下部焊层
void 焊接空隙
weld flow mark 焊接流痕
weld flush 焊缝凸起
weld line 焊接纹
weld mark 焊接痕
weld penetration 熔接透入
weld zone 焊接区
welding 焊接
welding bead 焊接泡
welding direction 焊接方向
welding distortion 焊接变形
welding flux 焊剂
welding ground 电熔接地
welding interval 焊接周期
welding stress 熔接应变
welding torch 熔接气炬
塑胶原料
acrylic 压克力
casein 酪素
cellulose acetate 醋酸纤维素CA
cellulose acetate butyrate 醋酸丁酸纤维素CAB
composite material 复合材料
cresol resin 甲酚树脂CF
dially phthalate 苯二甲酸二烯丙酯
disperse reinforcement 分散性强化复合材料
engineering plastics 工程塑胶
epoxy resin 环氧树脂EP
ethyl cellulose 乙基纤维素
ethylene vinylacetate copolymer 乙烯-醋酸乙烯EVA
ethylene-vinlacetate copolyme 醋酸乙烯共聚物EVA
fiber reinforcement 纤维强化热固性/纤维强化复合材料
high density polyethylene 高密度聚乙烯HDPE
high impact polystyrene 高冲击聚苯乙烯HIPS
high impact polystyrene rigidity 高冲击性聚苯乙烯
low density polyethylene 低密度聚乙烯LDPE
melamine resin 三聚氰胺酚醛树脂MF
nitrocellulose 硝酸纤维素
phenolic resin 酚醛树脂
plastic 塑胶
polyacrylic acid 聚丙烯酸PAP
polyamide 耐龙PA
polybutyleneterephthalate 聚对苯二甲酸丁酯PBT
polycarbonate 聚碳酸酯PC polyethyleneglycol 聚乙二醇PFG
polyethyleneoxide 聚氧化乙烯PEO
polyethyleneterephthalate 聚乙醇对苯PETP
polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA
polyoxymethylene 聚缩醛POM
polyphenylene oxide 聚硫化亚苯
polyphenyleneoxide 聚苯醚PPO
polypropylene 聚丙烯PP
polystyrene 聚苯乙烯PS
polytetrafluoroethylene 聚四氟乙烯PTFE
polytetrafluoroethylene 聚四氟乙烯
polythene 聚乙烯PE
polyurethane 聚氨基甲酸酯PU
polyvinylacetate 聚醋酸乙烯PVAC
polyvinylalcohol 聚乙烯醇PVA
polyvinylbutyral 聚乙烯醇缩丁醛PVB
polyvinylchloride 聚氯乙烯PVC
polyvinylfuoride 聚氟乙烯PVF
polyvinylidenechloride 聚偏二氯乙烯PVDC
prepolymer 预聚物
silicone resin 硅树脂
thermoplastic 热塑性
thermosetting 热固性
thermosetting plastic 塑胶
unsaturated polyester 不饱和聚酯树脂
歡迎來到Bewise Inc.的世界，首先恭喜您來到這接受新的資訊讓產業更有競爭力，我們是提供專業刀具製造商，應對客戶高品質的刀具需求，我們可以協助客戶滿足您對產業的不同要求，我們有能力達到非常卓越的客戶需求品質，這是現有相關技術無法比擬的，我們成功的滿足了各行各業的要求，包括：精密HSS DIN切削刀具、協助客戶設計刀具流程、DIN or JIS 鎢鋼切削刀具設計、NAS986 NAS965 NAS897 NAS937orNAS907 航太切削刀具,NAS航太刀具設計、超高硬度的切削刀具、醫療配件刀具設計、汽車業刀具設計、電子產業鑽石刀具、木工產業鑽石刀具等等。我們的產品涵蓋了從民生刀具到工業級的刀具設計；從微細刀具到大型刀具；從小型生產到大型量產；全自動整合；我們的技術可提供您連續生產的效能，我們整體的服務及卓越的技術，恭迎您親自體驗！！
BW Bewise Inc. Willy Chen willy@tool-tool.com bw@tool-tool.com www.tool-tool.comskype:willy_chen_bw mobile:0937-618-190 Head &Administration OfficeNo.13,Shiang Shang 2nd St., West Chiu Taichung,Taiwan 40356 http://www.tool-tool.com/ FAX:+886 4 2471 4839 N.Branch 5F,No.460,Fu Shin NorthRd.,Taipei,Taiwan S.Branch No.24,Sec.1,Chia Pu East Rd.,TaipaoCity,Chiayi Hsien,Taiwan
Welcome to BWtool world! We are an experienced tool maker specialized in cuttingtools. We focus on what you need and endeavor to research the bestcutter to satisfy users’demand. Our customers involve wide range of industries, like mold &die, aerospace, electronic, machinery, etc. We are professional expertin cutting field. We would like to solve every problem from you. Pleasefeel free to contact us, its our pleasure to serve for you. BW product including: cutting tool、aerospace tool .HSS DIN Cutting tool、Carbide end mills、Carbide cutting tool、NAS Cutting tool、NAS986 NAS965 NAS897 NAS937orNAS907 Cutting Tools,Carbide end mill、disc milling cutter,Aerospace cutting tool、hss drill’Фрезеры’Carbide drill、High speed steel、Milling cutter、CVDD(Chemical Vapor Deposition Diamond )’PCBN (Polycrystalline Cubic Boron Nitride) ’Core drill、Tapered end mills、CVD Diamond Tools Inserts’PCD Edge-Beveling Cutter(Golden Finger’PCD V-Cutter’PCD Wood tools’PCD Cutting tools’PCD Circular Saw Blade’PVDD End Mills’diamond tool ‘Single Crystal Diamond ‘Metric end mills、Miniature end mills、Специальные режущие инструменты ‘Пустотелое сверло ‘Pilot reamer、Fraises’Fresas con mango’ PCD (Polycrystalline diamond) ‘Frese’Electronics cutter、Step drill、Metal cutting saw、Double margin drill、Gun barrel、Angle milling cutter、Carbide burrs、Carbide tipped cutter、Chamfering tool、IC card engraving cutter、Side cutter、NAS tool、DIN or JIS tool、Special tool、Metal slitting saws、Shell end mills、Side and face milling cutters、Side chip clearance saws、Long end mills、Stub roughing end mills、Dovetail milling cutters、Carbide slot drills、Carbide torus cutters、Angel carbide end mills、Carbide torus cutters、Carbide ball-nosed slot drills、Mould cutter、Tool manufacturer.
Bewise Inc. www.tool-tool.com
ようこそＢｅｗｉｓｅ Ｉｎｃ.の世界へお越し下さいませ、先ず御目出度たいのは新たな
情報を受け取って頂き、もっと各産業に競争力プラス展開。
弊社は専門なエンド・ミルの製造メーカーで、客先に色んな分野のニーズ、
豊富なパリエーションを満足させ、特にハイテク品質要求にサポート致します。
弊社は各領域に供給できる内容は：
（１）精密ＨＳＳエンド・ミルのＲ＆Ｄ
（２）Carbide Cutting tools設計
（３）鎢鋼エンド・ミル設計
（４）航空エンド・ミル設計
（５）超高硬度エンド・ミル
（６）ダイヤモンド・エンド・ミル
（７）医療用品エンド・ミル設計
（８）自動車部品＆材料加工向けエンド・ミル設計
弊社の製品の供給調達機能は：
（１）生活産業～ハイテク工業までのエンド・ミル設計
（２）ミクロ・エンド・ミル～大型エンド・ミル供給
（３）小Ｌｏｔ生産～大量発注対応供給
（４）オートメーション整備調達
（５）スポット対応～流れ生産対応
弊社の全般供給体制及び技術自慢の総合専門製造メーカーに貴方のご体験を御待ちしております。
BewiseInc. talaşlı imalat sanayinde en fazla kullanılan ve üç eksende (x,y,z)talaş kaldırabilen freze takımlarından olan Parmak Freze imalatçısıdır.Çok geniş ürün yelpazesine sahip olan firmanın başlıca ürünleriniKarbür Parmak Frezeler, Kalıpçı Frezeleri, Kaba Talaş Frezeleri, KonikAlın Frezeler, Köşe Radyüs Frezeler, İki Ağızlı Kısa ve Uzun KüreselFrezeler, İç Bükey Frezeler vb. şeklinde sıralayabiliriz.
BW специализируетсяв научных исследованиях и разработках, и снабжаем самымвысокотехнологичным карбидовым материалом для поставки режущих /фрезеровочных инструментов для почвы, воздушного пространства иэлектронной индустрии. В нашу основную продукцию входит твердый карбид/ быстрорежущая сталь, а также двигатели, микроэлектрические дрели, ICкартонорезальные машины, фрезы для гравирования, режущие пилы,фрезеры-расширители, фрезеры-расширители с резцом, дрели, резаки формдля шлицевого вала / звездочки роликовой цепи, и специальные наноинструменты. Пожалуйста, посетите сайт www.tool-tool.com для получения большей информации.
BWis specialized in R&D and sourcing the most advanced carbidematerial with high-tech coating to supply cutting / milling tool formould & die, aero space and electronic industry. Our main productsinclude solid carbide / HSS end mills, micro electronic drill, IC cardcutter, engraving cutter, shell end mills, cutting saw, reamer, threadreamer, leading drill, involute gear cutter for spur wheel, rack andworm milling cutter, thread milling cutter, form cutters for splineshaft/roller chain sprocket, and special tool, with nano grade. Pleasevisit our web www.tool-tool.com for more info.
