HHO氫氧燃料省油器 (3)
EFIE (electronic fuel injector enhancer) with
HHO generator current limit PWM controller (optional)
電子噴油強化器暨限電流式電源管理控制器(選購)
HiGold110 version 1.0
謝謝您邁向綠色環保的一步.提高能源效率是減少您愛車碳足跡的最基本方案!
Put your money in the bank, not in the tank! 把錢存在銀行才對, 不是丟進汽車油箱.
功能
１．可從車內配線盒連接至電路板作為電源開關．當汽車鑰匙轉至啟動時才提供電路板電力．
電源電壓自動量測，10~15V範圍判定為12V，18~30V範圍判定為24V．
電源電壓指示燈 LED 綠色0805，當 DC in>12V時恆亮，當 DC in<12V時閃爍．
電源電壓指示燈 LED 藍色0805，當 DC in>24V時恆亮，當 DC in<24V時閃爍．
２．LED顯示
採四位數七段式，最左一位數為功能MODE，右三位數為該功能的數值．
以按鍵開關切換功能，並以按鍵開關設定數值．
功能按鍵開關顯示順序分為，並依此循環．
１．負載Duty
２．頻率Frequency
３．降低溫度Break Temp
４．截止溫度Stop Temp
５．低電壓Vcut off．關閉顯示Display off
設定按鍵開關分為＂加Up＂，＂減Down＂．
３．電瓶電壓過低保護，避免電瓶過度放電．
電源電壓低於Vcut自動切斷．
Vcut值分成10, 10.5, 11, 11.5, 12, 12.5, 22, 22.5, 23, 23.5, 24, 24.5V．
４．以電路板上的金屬微歐姆電阻回饋方式限制輸出電流，避免HHO電解槽輸出超
過所限定的．
負載Duty的最大輸出百分率，分為16階，
範圍0~100%．100%的 電流極限值Imax依產品規格．
數值分0, 6, 12, 18, 25, 31, 37, 43, 50, 56, 62, 68, 75, 81, 87, 93, 100%．
５．輸出的電流可以調整其震盪頻率Frequency．
頻率的單位是100Hz，分為16階，範圍100~25KHz．
數值分成1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 20, 50, 100, 150, 200, 250．
６．透過自動調整輸出電流大小來調整HHO電解槽電解溫度，避免電解槽過熱．
基本原理是透過電解槽加裝負溫度係數型溫度熱敏電阻傳感器
(NTC thermal resistor, 10K ohm, 1% 5V)取得實際溫度後，
以使用者設定的溫度作為自動控制電流的依據．
電路板本體提供 2.54mm插頭連接溫度傳感器．
輸出電流 Iout 降低的斜度同時由兩組溫度開關調整大小．
開始降低輸出之溫度Break Temperature Tb
數值可以是39, 42, 45, 48, 51, 54, 57, 60℃．
完全截止輸出之溫度Stop Temperature Ts
數值可以是60, 62, 64, 68, 70, 72, 74, 76, 78, 80℃．
Ts值設定>=Tb，電路板微電腦將以Tb為允許之最低溫度選定值．
目前HHO電解槽工作溫度 T，輸出電流將依比例下降：
當T<Tb， Iout = Imax．
當Tb<T<Ts， Iout = Imax * (Ts-T)/(Ts-Tb)．
當T>Ts， Iout = 0．
７．電路板有6個M4螺絲固定孔，方便固定．
四組輸出入接點，方便並聯至多四組HHO電解槽．
微電腦超低功率消耗設計．
台灣設計製造．
8．OBD1 (1996年前) 及OBD2(1996以後)可利用汽車診斷電腦協助監控，
盡量調整O2 sensor, MAF/MAP sensor, IAT, CST sensor，使短期供油修正
STFT及長期供油修正LTFT接近0%．
相關解說：
Additive(LTFT) & Multiplicative(STFT)是啥東東
汽車修理保養相關資源總整理
規格
輸入電壓範圍 4.8~40.0V．
綠藍色LED電源指示燈．
最大輸出電流75A．
輸出震盪頻率可調範圍100~25KHz．
工作環境溫度範圍 -20~85℃．
儲存環境溫度範圍 -40~105℃．
溫度讀取精密度1℃．
溫度傳感器10K 歐姆 5mm圓片型，精密度１%．
限電流式脈衝寬度變調電路設計方式控制．
總消耗功率小於14watt @ 12V 55A．
套件包含
1 x PWM PCB 控制電路板．
1 x PWM 鋁殼 (選購品)
1 x 鋁擠型LED顯示/控制盒
1 x 溫度傳感器 10K歐姆 5mm disk type.
1 x 溫度傳感線(長度60cm，選購品)．
8 x 電線線端端子 (適用電線等級 AWG 12~10)．
2 x 二線式線對板母座插頭 (給溫度傳感器及車內電源開關電線用)．
不提供列印的使用手冊，僅以email提供pdf檔．
Thank you for going green.
#1 solution for lowering your vehicle carbon footprint!
Function
1. Power On LED:
Automatic battery voltage measurement (jumper free).
DC range 10~15V judged as 12V.
Green LED lamp is on if power exceeds 12V, and flashes when below 12V.
When DC range is 18~30V judged nominal as 24V.
Blue LED lamp is lit if power exceeds 24V, and flashes when below 24V.
2. Auto low voltage cut off protection for battery.
Auto cut off when DC in<12V for 12V battery.
Auto cut off when DC in<24V for 24V battery.
3. Output current is limited through the feedback of onboard micro resistor to protect the HHO generator from drawing current larger than desired.
Output duty (Imax) can be adjusted by potentiometer (10K ohm 1%), ranges 0~100%
Duty percentage is divided to 16 grades, the value can be 0, 6.25, 12.5, 18.75, 25.0, 31.25, 37.5, 43.75, 50, 56.25, 62.5, 68.75, 75, 81.25, 87.5, 93.75, 100%
4. Output frequency can be adjusted by potentiometer.
Frequency can be adjusted by potentiometer (10K ohm 1%).
The frequency can be viewed from the in car LED bar display box connected from the main PWM PCB.
Frequency can be 100, 200, 300, 400, 500, 600, 700, 800, 900, 1k, 2k, 5k, 10k, 15k, 20k, 25kHz.
5. HHO Cell thermal sensor and temperature control
Thermal sensor uses negative thermal coefficient thermal resistor (NTC type) 10k ohm 1% 5V.
Sensor is connected to PCB with a 2.54mm pitch 2 pin connector.
Output current (Iout) can be adjusted by break temperature and stop temperature respectively.
Temperature protection function can be On/Off where On=Closed, and Off=Open).
Break temperature (Tb) can be 40, 45, and 50℃, use green jumper to select where Closed=Selected.
Stop temperature (Ts) can be 50, 55, 60, 65, 70, 75, 80℃, use red jumper to select where Closed=Selected.
The two temperatures can be selected with the jumpers on PCB.
The desired temperature is selected when the jumper circuit is closed.
The output current is automatically reduced when HHO generator temperature exceeds break temperature Tb.
Iout = Imax when T<Tb.
Iout = Imax * (Ts-T)/ (Ts-Tb) when T>Tb
where 0<Imax<55A.
If no jumper present, lowest temperature will be used by the micro processor.
If more than one jumper present, only the lowest temperature will be selected by the micro computer.
6. There are four M4 type screw holes on PCB for mounting.
The PCB preserves one socket for in car power on/off switch for forcing the PCB to power on or off.
In car On/Off switch withduty/frequency LED indicator PCB linked from PWM PCB by USB cable.
Onboard output connectors supplied for up to four HHO parallel cells.
Extremely low power consumption micro computer design.
Made in Taiwan.
Specification
Operating voltage range: 4.8~40.0V.
Power on indicator: green & blue color LED.
Maximum output current: 55A.
Output frequency range: 100~25KHz.
Ambient operating range: -20~85℃
Ambient storage range: -40~105℃
Temperature gradation: 5℃.
Current limit pulse width modulation (PWM) control.
Total power consumption is 14 watts at 12V/ 55A.
Package
1 x PWM PCB.
1 x PWM aliminum case (optional).
1 x Aluminum LED display/control box.
1 x Thermal sensor 10K ohm.
1 x Thermal sensor cable (60cm, optional).
12 x spade terminal (for cupper wire AWG 10).
2 x two-pin female wire-to-board connector (for sensor and power switch wire).
No printed user manual will be provided. Only acrobat pdf file will be sent to buyer by email.
